Scientific Papers

Below, you can find links to papers and Dr Thomas Lagö’s profile and his link to Linkedin. You can also find a list of Thomas Lagö’s publications.

https://www.linkedin.com/pub/thomas-lagö/5/b78/9b1

http://www.avhandlingar.se/om/Thomas+Lagö/

International Journals and Magazines

Thomas L. Lagö, Sven Olsson and Per Eriksson, “An Efficient Sampling Technique Applied in an Acoustic Doppler Current Meter,” Society for Experimental Mechanics, Experimental Techniques, [Pat] November/December 1999, pages [Pat] 29-32.

Thomas L. Lagö, Sven Olsson and Per Eriksson, “A Novel Signal Model for Acoustic Doppler Current Meters Based on Large Real-life Data Sets,” Submitted for publication in the IEEE Journal of Oceanic Engineering, Part I, March, 1999.

Thomas L. Lagö, Sven Olsson and Per Eriksson, “The Symmiktos Method: A non-linear Doppler Estimation Method for Acoustic Doppler Current Meters,” Submitted for publication in  the IEEE Journal of Oceanic Engineering, Part II, April, 1999.

Thomas L. Lagö, “Is Sampling Twice the Maximum Frequency a Correct Sampling Method?” Submitted for publication in The Journal of Applied Sensing Technologies, submitted December 1999, USA, revised December 2000, revised September 2001.

M. Winberg, S. Johansson, T. Lagö, I. Claesson, ”A New Active Headset for a Helicopter Application,” International Journal of Acoustics and Vibration, ISSN 1027-5851, June 1999, Volume 4, Number 2, pages 51-57.

Thomas L. Lagö and Sven Olsson, “Acoustic Doppler Current Meter Backscattering Distribution Properties, Analyzed Using Large Real Life Data Sets,” submitted for publication in the International Journal of Experimental Mechanics, Society for Mechanical Engineering, December 2001.

Thomas L. Lagö, “Sampling According to Nyquist and Shannon,” Sound and Vibration, The Noise and Vibration Control Magazine, Sound and Vibration Magazine, pages 20-22, February 2002.

Thomas L. Lagö, “The Historical Philosophies of Some High-Tech Companies,” Sound and Vibration Magazine, February 2003, Contributing Editor.

Anders Brandt, Thomas Lagö and Kjell Ahlin, “A Smart Way to Analyze Dynamic Measurements,” Sound and Vibration Magazine, February 2003, pages 20-23.

Thomas L. Lagö, “Quality from Poland – No Joke,”  Sound and Vibration Magazine, June 2003, Pages 5-6, Contributing Editor.

Thomas L. Lago, “Multiple Peak Count Analysis for Increased Spectral Resolution, a Nonlinear Filtering Method,” Journal of Aerospace, Paper No. 2003-01-3047, September 2004.

Anders Brandt, Thomas Lagö, Kjell Ahlin and Jiri Tuma, “Main Principles and Limitations of Current Order Tracking Methods,” Sound and Vibration Magazine, March 2005, pages 19-22.

Mathias Winberg, Thomas Lagö, Sven Johansson, Lars H kansson and Ingvar Claesson, “AVIIS, Active Vibration Isolation In Ships: A Pre-Analysis of the Sound and Vibration Problems,”IJAV – International Journal of Acoustics and Vibration, 10(4), pp 175-196, April 2005.

Thomas Lagö, “Multiple Peak Count Analysis for Increased Spectral Resolution, a Non-Linear Filtering Method.” SAE Transactions Journal of Aerospace, July 2005.

Anders Brandt, Thomas L. Lagö, and Kjell Ahlin, “Using Matlab for Advanced Noise and Vibration Analysis.” SAE Transactions Journal of Aerospace, July 2005.

Anders Brandt, Thomas L. Lagö, and Kjell Ahlin, “Noise and Vibration Measurement System Basics,“  Sound and Vibration Magazine, April 2006, pages 9-11.

Thomas L. Lagö, Rolf Zimmergren, Alan Boyer, Ingvar Claesson, Lars Håkansson and Bengt Magnhagen, “New Cutting Technology Provides Improved Workpiece Finish and Increased Tool Life,” Sound and Vibration Magazine, October 2006,S&V Observer, page 2.

I. Gustavsson, J. Zackrisson, Kristian Nilsson, Javier Garcia-Zubia, L. Håkansson, I. Claesson, and T. Lagö, “A Flexible Instructional Electronics Laboratory with Local and Remote Lab Workbenches in a Grid,” International Journal of Online Engineering, ISSN 1861-2121, Vol. 4, No 2 (2008). Invited.

I. Gustavsson, K. Nilsson, J. Zackrisson, J. Garcia-Zubia, U. Hernandez-Jayo, A. Nafalski, Z. Nedic, Ö. Göl, J. Machotka, M. I. Pettersson, T. Lagö, L. H kansson, “On objectives of instructional laboratories, individual assessment, and use of collaborative remote laboratories,” Accepted for publication in IEEE Transactions on Learning Technologies, TLTSI-2009-03-0049. Pre-published in IEEE Xplore (2009). Vol 2, No 4, 2009.

H.  Åkesson, T. Smirnova, T. Lagö, L. Håkansson and I. Claesson, “Investigation of the Dynamic Properties of a Milling Tool Holder,” Research Report No 2009:14, Blekinge Institute of Technology, ISSN: 1103-1581, November, 2009.

Ingvar Gustavsson, Lena Claesson, Kristian Nilsson, Johan Zackrisson, Zubia Garcia, Hernandez Javier, Unai Jayo, Lars Håkansson, Bartunek Josef Ström, Thomas Lagö, Ingvar Claesson, The VISIR Open Lab Platform.

Ingvar Gustavsson, Lena Claesson, Kristian Nilsson, Ingvar Claesson, Thomas Lagö, Lars Håkansson and Ingvar Claesson, Internet-Based Remote Laboratories: System architectures for remote laboratories – system design, hardware and interfacing, software issues, networking and network security, scalability and maintainability, IAOE Publications.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Initial Development of an Actuator Positioning Method for Active Boring Bars,” submitted for publication in Journal of Mechanical Systems & Signal Processing, September, 2010.

H. Åkesson, T. Smirnova, I. Claesson, T. Lagö and L. Håkansson, ”Estimation and Simulation of Nonlinear Dynamic Properties of a Boring bar”, accepted publication in IJAV – International Journal of Acoustics and Vibration, March, 16(1), pp.35-43, 2011.

International Proceedings with peer review

T. Lagö, P. Eriksson, M.  sman, “The Symmiktos Method: A Robust and Accurate Estimation Method for Acoustic Doppler Current Estimation,” Institute for Electrical and Electronics Engineers, Oceans ’93, 1993.

T.L. Lagö, P.F.B. Eriksson, M.  sman, “On Robust Estimation of Water Current Using a Frequency Domain Approach: The Symmiktos Method,”  Institute for Electrical and Electronics Engineers, Oceans ’94, pages I-335-340, France, 1994.

P. Sjösten, T. Lagö, K. Gunnarsson, “Predicition of Noise Reduction in a Ship for Active Vibration Control,” Society for Experimental Mechanics, Proceedings of the Fifteens International Modal Analysis Conference, IMAC-XII, 1994.

H. Håkansson, T. L. Lagö and S. Olsson, “A Non-tachometer Based Order Analysis Method for Interior Noise Measurements in Cars”, Society for Experimental Mechanics, Proceedings of the Twelve International Modal Analysis Conference, IMAC-XII, Vol II, pp 1491-1495, USA, 1994.

P. Sjösten, T. L. Lagö and K. Gunnarsson, “Prediction of Noise Reduction in a Ship for Active Vibration Control”, Society for Experimental Mechanics, Proceedings of the Twelve International Modal Analysis Conference, IMAC-XII, Vol II, pp 1763-1768, USA, 1994.

Thomas L. Lagö and Per F.B. Eriksson, “A Non-Gaussian Backscattering Signal Model for An Acoustic Doppler Current Meter,” Hydroakustik -95, KTH, Stockholm, 1995.

T. L. Lagö, M. Åsman  and Per F. B. Eriksson, “Short-time Spectral Estimation of Acoustic Doppler Current Meter Data,”  Institute for Electrical and Electronics Engineers, Oceans ‘96, 1996.

Thomas L. Lagö, Per G. Sjösten and P-A Hellström, “Evaluations of Field Tests for a MIMO ANC System Used in a Fishing Boat,” Society for Experimental Mechanics, Proceedings of the Fifteenth International Modal Analysis Conference, IMAC-XV, [Pat] pages 880-884, 1997.

Thomas L. Lagö, Sven Johansson and P-A Hellström, “Analysis of Helicopter Sound for the Development of a New Generation Active Headset,” Society for Experimental Mechanics, Proceedings of the Fifteenth International Modal Analysis Conference, IMAC-XV, [Pat] pages 1708-1714, 1997.

Per Sjösten, Thomas L. Lagö and Sven Johansson, “Evaluations of Field Tests for a Multiple Reference ANC System in a Patrol Boat,” Society for Experimental Mechanics, Proceedings of the Fifteens International Modal Analysis Conference, IMAC-XV, [Pat] pages 885-888, 1997.

Sven Johansson, Thomas L. Lagö, Ingvar Claesson and Sven Nordebo, “ANVC Performance and Robustness for Different Error Sensor Disturbance Signals,” Society for Experimental Mechanics, Proceedings of the Fifteenth International Modal Analysis Conference, IMAC-XV, [Pat] pages 1715-1721, 1997.

Per Sjösten, Thomas L. Lagö and Sven Johansson, “Evaluations of Field Tests for a Multiple Reference ANC System in a Patrol Boat,” Society for Experimental Mechanics, Proceedings of the Fifteenth International Modal Analysis Conference, IMAC-XV, [Pat] pages 885-888, 1997.

S. Johansson, T. L. Lagö, I. Borchers & K. Renger, “Performance of a Multiple versus Single Reference MIMO ANC Algorithm based on a Dornier 328 test data set,” International Institute for Acoustics and Vibration,  Proceedings of Active-97, pages 521-528, 1997.

Thomas Lagö and Ingvar Claesson, “Spectral Estimation Errors When Using FFT Analyzers,” International Journal of Acoustics and Vibration, Proceedings of the Fifth International Congress on Sound and Vibration, ICSV5, Adelaide, December 1997.

P. Sjösten, M. Hermodson, L. Feng, H. Samuelsson, S. Einarsson-Papadio and T. L. Lagö,” Active Vibration Control on a Light High Speed Train: Preliminary Results,” Proceedings of InterNoise-97, August, 1997.

T. L. Lagö, “Active Vibration Reduction in a Light High Speed Train Bogie,” Society for Experimental Mechanics, Proceedings of the Sixteenths International Modal Analysis Conference, IMAC-XVI, pages [Pat] 240-246, 1998.

M. Winberg, T.L. Lagö, I. Claesson, ”Speaking Panels – An ANVC System with Inertial Mass Actuators,” International Noise Control Engineering, Proceedings of Inter-Noise 98, paper  #535, 1998.

M. Winberg, T.L. Lagö, “Inertial Mass Active Mounts Used in a Marine Application,” Proceedings of the Adaptronic Congress 99, Interdisciplinary Forum on Adaptive Technologies and Systems in Industrial Applications, Potsdam, Berlin, March 1999.

Julien Maillard, Thomas L. Lagö, Mathias Winberg and Chris Fuller, “Fluid Wave Actuator for the Active Control of Hydraulic Pulsations in Piping Systems,” Society for Experimental Mechanics, International Modal Analysis Conference, IMAC-XVII, Orlando Florida, February, 1999.

Ingvar Claesson, Lars Håkansson and Thomas L. Lagö, “Robust Control of Machine-tool Vibration in a Lathe,” International Institute of Acoustics and Vibration, Proceedings of the Sixth International Conference for Sound and Vibration, ICSV6, Vol 4, pages 1719-1730, 1999.

Sven Johansson, Thomas L. Lagö and Ingvar Claesson, “Performance of a Single versus a Twin-Reference Controller in Narrowband Active Noise Control Applications,” Society for Experimental Mechanics, Proceedings of the Seventeenth International Modal Analysis Conference, IMAC-XVII, [Pat] pages 356-362, 1999.

Sven Olsson, Thomas L. Lagö and Ingvar Claesson, “Custom-designed Filters Through Time-window Modification ,” Society for Experimental Mechanics, Proceedings of the Seventeenth International Modal Analysis Conference, IMAC-XVII, [Pat] pages 1145-1149, 1999.

S. Olsson, T. L. Lagö and H. Håkansson, “A Fast Multiplane Shaft Balancing Method with Adaptive Features,” Society for Experimental Mechanics, Proceedings of the Seventeenth International Modal Analysis Conference, IMAC-XVII, [Pat] pages 1681-1685, 1999.

Mathias Winberg, Thomas Lagö and C. Brandel, “Sound Measurements Using a Large Microphone Array,” Society for Experimental Mechanics, Proceedings of the Seventeenth International Modal Analysis Conference, IMAC-XVII, [Pat] pages 397-400, 1999.

L. Håkansson, I. Claesson and T. Lagö, “Active Control of Machine Tool Chatter,” IMAC-XVII, Society for Experimental Mechanics, Proceedings of the Seventeenth International Modal Analysis Conference, Orlando Florida, [Pat] pages 1826-1831, February, 1999.

Julien Maillard, Thomas L. Lagö, Mathias Winberg and Chris Fuller, “Fluid Wave Actuator for the Active Control of Hydraulic Pulsations in Piping Systems,” Society for Experimental Mechanics, Proceedings of the Seventeenth International Modal Analysis Conference, IMAC-XVII, Orlando Florida, [Pat] pages 1806-1812, February, 1999.

Per Persson, Thomas L. Lagö, and Arvid Norberg, “Active Control of Sleeper-Induced Sound in a High Speed Train,“ International Institute of Acoustics and Vibration, Proceedings of the Sixth International Conference for Sound and Vibration, ICSV6, Vol 4, pages 1747-1752, 1999.

Linus Pettersson, Lars H kansson, Ingvar Claesson and Thomas Lagö, “Piezo Ceramic Actuators versus High Magnetostrictive Actuators in the Active Control of Tool Vibration,” European Acoustics Association: Forum Acusticum, Structural Acoustics and Vibration, pages 1-6, 1999.

Thomas L. Lagö. “Lightweight High Speed Train Bogie Active Vibration Control with Acoustic Minimization,” International Association for Vehicle System Dynamics, Best Poster Paper Award at the 16th Symposium on “Vehicle Dynamics,” South Africa, 1999.

Lars Håkansson, Ingvar Claesson and Thomas L. Lagö, “Active Control of Chatter in Turning,” Society for Experimental Mechanics, Proceedings of the Seventeenth International Modal Analysis Conference, IMAC-XVII, [Pat] pages 1799-1805, 1999.

Thomas Lagö and Sven Olsson, “An Efficient Sampling Technique for Industrial Applications,” Proceedings of Internoise-99, pages 1629-1632, August 1999, Nice, France.

Lars Håkansson, Ingvar Claesson, Linus Pettersson and Thomas L. Lagö, “Active Control Machine Tool Chatter Using Piezo Ceramic Actuators in Tool Holder Shank,” American Society for Mechanical Engineers, DETC99, 1999.

Thomas Lagö and Sven Olsson, “A Non-linear Filtering Method For Underwater Applications,” Proceedings of InterNoise-99, pages 1623-1628, August 1999, Nice, France.

M. Winberg, S. Johansson and T. L. Lagö, “Control Approaches for Active Noise and Vibration Control in a Naval Application,” International Institute of Acoustics and Vibration, Proceedings of the Seventh International Conference for Sound and Vibration, ICSV7, pages 241-248, Germany, 2000.

M. Winberg, S. Johansson and T. L. Lagö, “Evaluation of the Performance of an Active Noise Control System in an Aircraft Mock-up,” International Institute of Acoustics and Vibration, Proceedings of the Seventh International Conference for Sound and Vibration, ICSV7, pages 203-210, Germany, 2000.

T. Lagö, S. Olsson and P. Eriksson, “The Symmiktos Method®, A Non-Linear Approach to First Moment Estimation for Doppler Measurements,” International Institute of Acoustics and Vibration, Proceedings of the Seventh International Conference for Sound and Vibration, ICSV7, pages 3273-3280, Germany, 2000.

T. Lagö, G. Preti and L. Davis, “Frequency Domain Synchronous Averaging, A Novel Approach To Stable Averaging,” International Institute of Acoustics and Vibration, Proceedings of the Seventh International Conference on Sound and Vibration, ICSV7, pages 3321-3328, Germany, 2000.

T. Lagö and S. Olsson, “Spectral Resolution Enhancement Using A Non-linear Filtering Method,” International Institute of Acoustics and Vibration, Proceedings of the Seventh International Conference on Sound and Vibration, ICSV7, Germany, 2000.

S. Olsson, T. Lagö and H. Håkansson, “A Fast Multi-plane Shaft Balancing Method For Coupled Shafts,”  International Institute of Acoustics and Vibration, Proceedings of the Seventh International Conference for Sound and Vibration, ICSV7, pages, 691-696, Germany, 2000.

Thomas L. Lagö , Larry Davis and Giuseppe Preti, “Time and Frequency Domain Analysis Considerations In Automotive Applications,” Proceedings of SIAT-2001, Symposium on International Automotive Technology, pages 527-533, Society for Automotive Engineering, Pune, India, 2001.

Thomas L. Lagö , Larry Davis and Giuseppe Preti, “Averaging Techniques for Complex Signals in Automotive Applications,” Proceedings of SIAT-2001, Symposium on International Automotive Technology, pages 523-526, Society for Automotive Engineering, Pune, India, 2001.

Thomas L. Lagö, Sven Olsson, Mattias Dahl and Ingvar Claesson, “A  Novel Frequency Domain Time Window for accurate Amplitude Measurements Using The High Accuracy Flat Top Window, HAFT,” International Institute of Acoustics and Vibration, Accepted Abstract for the Eighth International Congress on Sound and Vibration, ICSV8, Hongkong, June 2001.

Thomas L. Lagö and Larry Davis, “Heisenberg’s Uncertainty Principle Applied to Time and Frequency Considerations for Acoustic Applications,” Accepted Abstract for InterNoise-2001, Holland, August 2001.

Thomas L. Lagö, “Increased Source Positioning and Enhanced Monitor Sound Field Using Alternative Loudspeaker Placement, Accepted  Abstract for Internoise2003, International Convention Center, Jeju, South Korea, August 25-28, 2003.

Thomas L. Lagö, “Multiple Peak Count Analysis Filtering for Increased Spectral Resolution, a Non-linear Filtering Method, Proceedings of the WAC2003 SAE Conference on Sound and Vibration, September 8-12, 2003, Montreal, Canada.

Thomas L. Lagö, “A Tonal Signal Model for Doppler Applications, Proceedings of the 10th International Conference on Sound and Vibration, ICSV10, July 7-10 2003, KTH, Stockholm, Sweden.

A.H. Brandt, T. L. Lagö, K. Ahlin, “Summary of Spectrum Estimators for Vibration Signals and Their Errors,” Society for Experimental Mechanics, Proceedings for the 22nd International Modal Analysis Conference, IMAC XXII, Dearborn, USA, January 2004.

Ingvar Claesson and Thomas L. Lagö, “A Historical Perspective on the FFT Algorithm,“ Society for Experimental Mechanics, Society for Experimental Mechanics, Proceedings for the 22nd International Modal Analysis Conference, IMAC XXII, Dearborn, USA, January 2004.

Anders Brandt, Thomas L. Lagö and Kjell Ahlin, “Interpolation and Resampling Methods in Time and Frequency Domain and Their Applications,” Society for Experimental Mechanics, Proceedings for the 22nd International Modal Analysis Conference, IMAC XXII, Dearborn, USA, January 2004.

T. Tran, M. Dahl, I. Claesson, and T.L. Lagö, “High Accuracy Windows for Today´s 24-bit ADCs,” Society for Experimental Mechanics, Proceedings of the 22nd International Modal Analysis Conference, IMAC XXII, Dearborn, USA, January 2004.

Thomas L. Lagö, “Multiple Peak Count Analysis Filtering for Increased Spectral Resolution, a Non-linear Filtering Method, Proceedings of the WAC2004 SAE Conference on Sound and Vibration, November 1-4, 2004, Reno, Nevada, USA.

Anders Brandt, Thomas L. Lagö and Kjell Ahlin, “Using Matlab for Advanced Noise and Vibration Analysis,” Proceedings of the WAC2004 SAE Conference on Sound and Vibration, November 1-4, 2004, Reno, Nevada, USA.

James J. Chatterley, Andrew J. Boone, Thomas L. Lagö, Jonathan D. Blotter, Scott D. Sommerfeldt, Craig C. Smith,  “Sound Quality of Sewing Machines,” Abstract for the 148th semi annual meeting of the Acoustical Society of America – ASA, in San Diego California, Nov 15 -18th 2004, USA.

James J. Chatterley, Andrew J. Boone, Thomas L. Lagö, Jonathan D. Blotter, Scott D. Sommerfeldt, Craig C. Smith,  “Sound Quality Assessment of Sewing Machines,” Proceedings of IDETC/CIE 2005 ASME 2005 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference September 24-28, 2005, Long Beach, California, USA.

Thomas L. Lagö, James J. Chatterley, Andrew J. Boone, Jonathan D. Blotter, Scott D. Sommerfeldt, Craig C. Smith, Andrew Boone and Anders Brandt,  “Sewing Machine Analysis,” Internal Report for Viking Sewing Machines, April 2005.

James J. Chatterley, Andrew J. Boone, Thomas L. Lagö, Jonathan D. Blotter, Scott D. Sommerfeldt, Craig C. Smith, “Sound Quality Assessment of Sewing Machines,” Abstract for the 20th Biennial Conference on Mechanical Vibration and Noise, in Long Beach California, Sept 25-28th 2005.

James J. Chatterley, Andrew J. Boone, Thomas L. Lagö, Jonathan D. Blotter, Scott D. Sommerfeldt, Craig C. Smith, “Sound Quality Assessment of Sewing Machines,” Abstract for the 149th semi annual meeting of the Acoustical Society of America – ASA, in Vancouver B.C. Canada, May 18th 2005.

Henrik  kesson, Tatiana Smirnova, Lars Håkansson, Ingvar Claesson and Thomas Lagö, “Analog versus Digital Control of Boring Bar Vibration,“ Proceedings of the SAE World Aviation Congress 2005, October 2005, Texas, USA.

Thomas L. Lagö and Anders Brandt, “Actual Accuracy in Flight Data Collection and Analysis,” Proceedings of the 2005 SAE World Aviation Congress, Texas, USA, October 2005.

Mathias Winberg and Thomas L. Lagö, “Speaking Panels – A New Actuator For Active Noise Control,” Proceedings of the 2005 Congress and Exhibition on Noise Control and Engineering, InterNoise2005, Rio de Janeiro, Brazil, August 7-10, 2005.

A. Brandt, J. Tuma, T. Lagö, and K. Ahlin, “Toolboxes for Analysis of Sound and Vibration Signals Within MATLAB,” MATLAB User Meeting 2005, Czech Republic.

H. Åkesson, A. Brandt, T. Lagö, L. Håkansson, I. Claesson, “Operational Modal Analysis of a Boring Bar During Cutting” published at the 1st IOMAC conference, April 26-27, 2005, Copenhagen, Denmark.

H. Åkesson, T. Smirnova, L. Håkansson, T. Lagö, I. Claesson, “Analog and Digital Approaches of Attenuation Boring Bar Vibrations During Metal Cutting Operations”, published at the 12th ICSV conference, Lisbon, Portugal, July 11 – 14, 2005.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Analog versus Digital Control of Boring Bar Vibration”, Accepted for publication In proceedings of the SAE World Aerospace Congress, WAC, Dallas, Texas, USA, October 3-6, 2005.

Thomas L. Lagö and Anders Brandt, “Typical Accuracy in Data Collection and Analysis,” Society for Experimental Mechanics, Accepted abstract for the 23rd International Modal Analysis Conference, 2006, St. Louis, Missouri USA.

H.Åkesson, I. Gustavsson, L. Håkansson, I. Claesson and T. Lagö, “Vibration Analysis of Mechanical Structures over the Internet Integrated into Engineering Education”, In proceedings of the 2006 ASEE Annual Conference & Exposition, Chicago IL, June 18 – 21, 2006.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson, A. Sigfridsson, T. Svensson and T. Lagö, “Active Boring Bar Prototype Tested in Industry ,” Accepted Paper, Adaptronic Congress 2006, 03-04 May, Göttingen, Germany.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson, A. Sigfridsson, T. Svensson and T. Lagö, “A First Prototype of an Active Boring Bar Tested in Industry”, In Proceedings of the Twelfth International Congress on Sound and Vibration, ICSV12, Lisbon, Portugal, 11 – 14 July, 2006.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Identification of Spatial Dynamic Properties of the Boring Bar by means of Finite Element Model: Comparison with Experimental Modal Analysis and Euler-Bernoulli Model”, In Proceedings of the Twelfth International Congress on Sound and Vibration, ICSV12, Lisbon, Portugal, 11 – 14 July, 2006.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Comparison of different controllers in the active control of tool vibration; including abrupt changes in the engagement of metal cutting”, Sixth International Symposium on Active Noise and Vibration Control, ACTIVE, Adelaide, Australia, 18-20 September, 2006.

T. Smirnova, H.Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Building an Accurate Finite Element Model of the Boring Bar with “Free-Free” Boundary Conditions: Correlation to Ex perimental Modal Analysis and Euler-Bernoulli Model”, Noise and Vibration Engineering Conference, ISMA, Leuven, Belgium, 18 – 20 September 2006.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Vibration in Turning and the Active Control of Tool Vibration”, Second World Congress on Engineering Asset Management and the Fourth International Conference on Condition Monitoring, Harrogate, UK, 11-14 June, 2007.

I. Gustavsson, J. Zackrisson, L. Håkansson, I. Claesson, and T. Lagö, “The VISIR project – an Open Source Software Initiative for Distributed Online Laboratories”, Proceedings of the 2007 REV Conference, Porto, Portugal, June 25 – 27, 2007.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Investigation of the Dynamic Properties of a Boring Bar Concerning Different Boundary Conditions”, ICSV14 – The Fourteenth International Congress on Sound and Vibration, Cairns, Australia, 9-12 July, 2007.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Initial Experiments With a Finite Element Model of an Active Boring Bar”,ICSV14 – The Fourteenth International Congress on Sound and Vibration, Cairns, Australia, 9-12 July, 2007.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson, A. Sigfridsson, T. Svensson and T. Lagö, “Investigation of the Dynamic Properties of a Passive Damped Boring Bar”, In Proceedings of Adaptronic Congress, Berlin, Germany, 20 – 21 May, 2008.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Advantages and Drawbacks Using Different Sensors in Feedback Control in Active Boring Bar Applications”, ICSV15 – The 15th International Congress on Sound and Vibration, Daejon, Korea, 6 – 10 July, 2008.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Investigation Concerning Actuator Position in an Active Boring Bar Regarding it´s Performance by Means of “3-D” Finite Element Models”, ICSV15 – The 15th International Congress on Sound and Vibration, Daejon, Korea, 6 – 10 July, 2008.

Thomas L. Lagö and Hector Lobo, “ENHANCING SPECTRAL RESOLUTION USING A NON-LINEAR APPROACH, THE MPCA METHOD, NSA-2008, December 22-24 2008, Visakhapatnam, India.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Dynamic Properties of Tooling Structure: Hydraulic Clamping versus Standard Screw Clamping in a Lathe Application”, Ninth International Conference on Computational Structures Technology, Athens, Greece, 2-5 September, 2008.

T. Smirnova, H.  Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Estimation of an active boring bar´s control path FRF:s by means of its 3-D FE-model with Coulomb friction”, The Ninth International Conference on Computational Structures Technology, Athens, Greece, 2-5 September, 2008.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Developments Steps of an Active Boring Bar for Industrial Application,” Internoise, Shanghai, China, 26-29 October, 2008.

M. Winberg, H.  Åkesson, T. Lagö, and I. Claesson, “Acoustical Measurements Using a Virtual Microphone Technique,” Internoise, Shanghai, China, 26-29 October, 2008.

I. Gustavsson, J. Zackrisson, J. Ström Bartunek, Kristian Nilsson, L. H kansson, I. Claesson, and T. Lagö, “Telemanipulator for Remote Wiring of Electrical Circuits,” Proceedings of the 2008 REV Conference, Düsseldorf, Germany, June 22 – 25, 2008.

K. Nilsson, J. Zackrisson and M. Pettersson, “Remote access of Computer Controlled Experiments”, Proceedings of the 2008 ICBL Conference, Floianopolis, Brazil, November 3 – 5, 2008.

I. Gustavsson, K. Nilsson, T. Lagö, ” On physical experiments and individual assessment of laboratory work in engineering education”, Proceedings of the ACM MEDES 2009 Conference, Lyon , France, October 27 – 30, 2009.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö “Preliminary investigation of active control of a milling tool holder, ACTIVE 2009 – The 2009 International Symposium on Active Control of Sound and Vibration, Ottawa, Canada, 20-22 August, 2009.

H. Åkesson, A. Sigfridsson, T. Lagö, I. Andersson and L. Håkansson, “Noise Source Identification and Active Control in a Water Turbine Application,” In Proceedings of The Sixth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Dublin, Ireland, 23-25 June, 2009.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Investigation of the Dynamic Properties of a Milling Structure; Using a Tool Holder with Moderate Overhang”, IMAC XXVII, Orlando, USA, 9-12 February, 2009.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Accurate FEM modeling of a Boring Bar Correlated with Experimental Modal Analysis”, IMAC XXVII, Orlando, USA, 9-12 February, 2009.

H.  Åkesson, A. Sigfridsson, T. Lagö, I. Andersson and L. Håkansson, “Noise Source Identification and Active Control in a Water Turbine Application”, In Proceedings of The Sixth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Dublin, Ireland, 23-25 June, 2009.

T. Smirnova, H.  Åkesson, I. Claesson, L. Håkansson and T. Lagö, “Modeling a Clamped Boring Bar using Euler-Bernoulli Beam Models with Various Boundary Conditions”,3rd Conference on Mathematical Modeling of Wave Phenomena/20th Nordic Conference on Radio Science and Communications, v1106, p149-156, 2009.

T. Smirnova, H.  Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Investigation Concerning Dynamic Properties of an Active Boring Bar Regarding its Performance by Means of “1-D” Finite Element Models”,ICSV16 – The Sixteenth International Congress on Sound and Vibration, Krakow, Poland, 5-9 July, 2009.

H.  Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Preliminary investigation of active control of a milling tool holder”, ACTIVE 2009 – The 2009 International Symposium on Active Control of Sound and Vibration, Ottawa, Canada, 20-22 August, 2009.

T. Smirnova, H.  kesson, L. Håkansson, I. Claesson and T. Lagö, “Simulation of Active Suppression of Boring Bar Vibrations by Means of Boring Bar’s “1-D” Finite Element Model”, ACTIVE 2009 – The 2009 International Symposium on Active Control of Sound and Vibration, Ottawa, Canada, 20-22 August, 2009.

Henrik  Åkesson, Andreas Sigfridsson and Thomas L. Lagö, “An on-line damping and monitoring of severe vibrations in a power plant – Granö in Sweden,” International Modal Analysis Conference, February 2010, Jacksonville, Florida, USA.

Henrik  Åkesson, Andreas Sigfridsson and Thomas Lagö, “Active Control of Turbine Vibration and Conditioning Based Monitoring,” Proceedings of International Conference for Sound and Vibration, ICSV 17, 18-22 July, 2010, Cairo, Egypt.

Henrik  kesson, Andreas Sigfridsson and Thomas Lagö, “Combining Active Control and Conditioning Based Monitoring using Embedded Piezo Sensors and Actuators,” Micro Systems Workshop, MSW Conference, May 2010, Stockholm, Sweden.

Thomas L. Lagö, “Condition Monitoring Solutions as a Tool to Saving Maintenance Cost,” CM 2010 and MFPT 2010, The Seventh International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Ettington Chase Stratford on Avon on 22nd to 24th June 2010, England.

Henrik  Åkesson, Andreas Sigfridsson, Thomas Lagö and Peter Berg, “EMERG-1, a wireless emergency system for a safer environment,” CM 2010 and MFPT 2010, The Seventh International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Ettington Chase, Stratford on Avon on 22nd to 24th June 2010, England.

Thomas Lagö, Henrik  Åkesson and Andreas Sigfridsson, “Proper Scaling Practices for Condition Based Monitoring Data,” CM 2010 and MFPT 2010, The Seventh International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Ettington Chase Stratford on Avon on 22nd to 24th June 2010, England.

Thomas L. Lagö,  Ingvar Claesson and Lars Håkansson, “The “Gauss Transform” for CBM Applications,” CM 2010 and MFPT 2010, The Seventh International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Ettington Chase Stratford on Avon on 22nd to 24th June 2010, England.

2010 H.  Åkesson, A. Sigfridsson and T. L. Lagö, “An on-line monitoring of forced excitation vibrations in a soccer stadium – Gamla Ullevi”, CM2010 and MFPT2010, The Seventh International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Ettington Chase, Stratford-upon-Avon, England, 22-24 June, 2010.

Thomas L. Lagö, “Condition Monitoring Solutions with Prognosis Capabilities,” CM 2011 and MFPT 2011, The Eighth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 20-22 June 2011, St David’s Hotel, Cardiff, Wales, UK.

Jay Nkuna, Henrik  Åkesson and Thomas Lagö, “Classification, Prognostics and Condition Based Maintenance (CBM) of Rolling Element Bearings based on Evolutionary Algorithm Optimizations of Kohonen’s Self-Organizing Maps,” MFPT, May 10-12, 2011, Virginia Beach, USA.

Thomas Lagö, Tierry Budge, Alan Boyer and Arthur Osgatharp, “Loudspeakers Designed for Increased Intelligibility Despite Lower Sound Pressure Levels,” Proceedings of InterNoise 2012, August 19-22, New York.

Thomas Lagö, Tierry Budge, Alan Boyer and Arthur Osgatharp, “Loudspeakers designed for accurate sonic boom and low frequency sound reproduction,” Proceedings of InterNoise 2012, August 19-22, New York.

Thomas L. Lagö, “Human Listening Tests In Production Lines,” CM2012, Proceedings of The Ninth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies at The Earl’s Court Ibis Hotel, London, UK.

Thomas L. Lagö, “How to properly find amplitude values in CBM applications,” CM2012, Proceedings of The Ninth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies at The Earl’s Court Ibis Hotel, London, UK.

Thomas L. Lagö, “Production Line Testing of Small Electrical Motors,” CM2012, Proceedings of The Ninth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies at The Earl’s Court Ibis Hotel, London, UK.

Thomas L. Lagö and Jay Nkuna, “Robust Classification of Gearbox Faults by means of Vibration Condition Monitoring and Evolutionary Optimisation of Kohonen’s Self-Organizing Maps,” CM2012, Proceedings of The Ninth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies at The Earl’s Court Ibis Hotel, London, UK.

Jay Nkuna and Thomas Lagö, “Parallel classification of rolling element bearing faults based on  fuzzy logic  and Kohonen’s Self-Organising Maps,” 18th World Conference on Non-Destructive Testing (WCNDT2012), Durban, South Africa, April 15-20, 2012.

Thomas L. Lagö, “Amplitude Errors due to Sparse Sampling Following Shannon,” MPMM 2012 Conference, Maintenance, Performance, Measurement & Management, 12th & 13th September 2012, University of Sunderland, Great Britain.

Thomas L. Lagö, “An Automatic Approach for Proper Amplitude Estimation in CBM Applications,” Proceedings of CM2013/MFPT2013 The Tenth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 18-20 June 2013, Qubus Hotel, Kraków, Poland.

Thomas L. Lagö, “Discretization’s Impact on Time Domain Analysis,” Proceedings of CM2013/MFPT2013 The Tenth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 18-20 June 2013, Qubus Hotel, Kraków, Poland.

Thomas L. Lagö and Alan Boyer, “International Experiences from a New Sound System Approach,” 134th AES Convention e-Brief, Fontana de Trevi Conference Center, May 4-7 2013, Rome, Italy.

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, ”NEW E-LEARNING APPROACHES FOR SOUND AND VIBRATION APPLICATIONS,” 6th International Conference from Scientific Computing to Computational Engineering, Athens, Greece, 9-12 July, 2014.

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, “NEW e-LEARNING AND MOOC APPROACHES FOR CBM APPLICATIONS, “ BINDT/CM 2014, Great Britain.

Thomas L. Lagö and Alan Boyer, “ DYNAMIC SIGNAL PROCESSING APPROACHES FOR BETTER SPEECH INTELLIGIBILITY IN MUSIC ACOUSTICS APPLICATIONS,” Proceedings of the 21st International Congress on Sound and Vibration, ICSV, 13-17 July, 2014, Beijing/China.

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, EFFECTIVE ACCURACY CONTROL FOR CBM APPLICATIONS,” Conference Proceedings of MFPT (the Society for Machinery Failure Prevention Technology), May 20-22, 2014,  Sheraton Oceanfront Hotel, Virginia Beach, VA, USA.

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, ”NEW E-LEARNING SYSTEMS FOR CBM APPLICATIONS,” Conference Proceedings of MFPT (the Society for Machinery Failure Prevention Technology), May 20-22, 2014,  Sheraton Oceanfront Hotel, Virginia Beach, VA, USA.

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, “NEW E-LEARNING, MOOC AND MOOL APPROACHES FOR CBM APPLICATIONS.

Thomas L. Lagö, “DYNAMIC SIGNAL PROCESSING APPROACHES FOR BETTER SPEECH INTELLIGIBILITY IN MUSIC ACOUSTICS APPLICATIONS,”

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, “NEW e-LEARNING AND MOOC APPROACHES FOR CBM APPLICATIONS, “ Proceedings of BINDT/CM 2014, June 2014, Manchester, Great Britain.

Invited Papers

T.L. Lagö, P.F.B. Eriksson, M. Åsman, “Performance of an Acoustic Doppler Current Estimation Method Based on The Symmiktos Method,” IEEE Fifth Working Conference on Current Measurements, pages 47-52, 1995, Invited Paper.

T. L. Lagö, M. Åsman  and Per F. B. Eriksson, “Short-time Spectral Estimation of Acoustic Doppler Current Meter Data,” International Institute of Electrical and Electronics Engineers, Oceans ‘96, pages 283-288, 1996, Invited Paper.

Thomas L. Lagö, “Field Test Evaluation of an Inertial Mass Active Vibration Reduction System on a High-Speed Train”, Engineered Adaptive Structures for Noise and Vibration Control, The Engineering Foundation, Invited Paper.

P. Sjösten, S. Johansson, T. L. Lagö and I. Claesson, “Active Noise Control in a Twin-Engine Patrol Boat,” International Noise Control Engineering, Inter-Noise 96, pages 1199-1202, 1996, Invited Paper.

Per Sjösten, S. Johansson, I. Claesson and Thomas L. Lagö, “Multi-reference Controllers for Active Control of Noise and Vibration,” Proceedings of the ISMA21 Conference, Leuven, 1996, pages 295-303, Invited Paper.

T. L. Lagö et.al., “Active Structural Acoustic Control for Light High Speed Trains,” Proceedings of the Engineering Foundation’s Conference: Engineered Composite Structures for Active Noise and Vibration Control,” Invited Paper, Canada, 1997.

Sven Johansson, Sven Nordebo, Thomas L. Lagö, Per Sjösten, Ingvar Claesson, I. U. Borchers and Klaus Renger, “Evaluation of a Multiple-versus a Single-reference MIMO ANC Algorithm on Dornier 328 Test Data,” ISMA 23, Invited Paper, Vol.II, pages 815-822, Leuven, 1998.

Per Persson, Thomas L. Lagö and Ingvar Claesson, “Active vibration reduction in a light-weight High-speed Train,” International Federation of Automatic Control, 1999, Invited Paper.

L. H kansson, I. Claesson, L. Pettersson, T. Lagö, “Embedded Piezo-ceramic Actuators In A Tool Holder Shank For The Active Control Of Machine-Tool Vibration,” International Noise Control Engineering, Active-99, pages 305-316, Fort Lauderdale, Dec 2-4 1999, Florida, USA. Invited Paper.

Linus Pettersson, Lars H kansson, Ingvar Claesson, and Thomas Lagö, “Nonlinear modeling of the Forward Path in a Mechanical Active Control System,” Proceedings of Forum Acusticum 1999, Acta Acustica, Vol 85, 1999, Page S101, Suppl. 1, Berlin March 14-19, 1999. Invited Paper.

Thomas L. Lagö and Sven Olsson, “A Non-linear Filtering Method for Underwater Applications,” International Noise Control Engineering, Inter-Noise ‘99, pages 1623-1628, USA, Invited Paper.

Thomas L. Lagö and Sven Olsson, “An Efficient Sampling Technique For Industrial Applications,” International Noise Control Engineering, Inter-Noise ‘99, pages 1629-1627, USA, Invited Paper.

Thomas L. Lagö and Sven Olsson, “Statistical Properties of Backscattering Signals from Doppler Current Measurement Systems,” Proceedings of the IEEE Sixth Conference on Current Measurements, USA, pages 269-274, Invited Paper.

Per Persson, Thomas L. Lagö and Ingvar Claesson, “Optimization of Loudspeaker and Microphone Positions for Active Noise Control Applications,” Society for Experimental Mechanics, International Modal Analysis Conference, IMAC-XVII, [Pat], 1999.

Per Persson, Thomas L. Lagö and Ingvar Claesson, “Active Vibration Reduction in a Light-weight High Speed Train Bogie,” IFAC-99, Beijing, China, July, 1999, Invited Paper.

Sven Johansson, Sven Nordebo, Thomas L. Lagö, Per Sjösten, Ingvar Claesson, Ingo U. Borchers and Klaus Renger, “Control Approaches For Active Control Of Propeller-Induced Cabin Noise Evaluated From Data From A Dornier 328 Aircraft,”International Institute of Acoustics and Vibration, ICSV7, pages 1611-1618, Invited Paper, 1999.

Sven Johansson, Sven Nordebo, Thomas L. Lagö, Ingvar Claesson, “Control Approaches for Active Control of Propeller Induced Cabin Noise Evaluated from Data from a Dornier 328 Aircraft,” International Institute of Acoustics and Vibration, Proceedings of the Sixth International Congress on Sound and Vibration, ICSV6, Lyngby, Denmark, pages 1611-1618, Invited Paper, July 1999.

Thomas L. Lagö, “Time and Frequency Consideration using Heisenberg’s Uncertainty Principle Applied in Mechanical and Acoustic Applications,” International Institute of Acoustics and Vibration, Proceedings of the Ninth International Congress on Sound and Vibration, ICSV9, Orlando, USA, Invited Paper, July 2002.

Thomas L. Lagö and Sven Olsson, “MPCA, a Non-linear Filtering Method for ADCM Spectral Resolution Enhancement,” International Institute of Acoustics and Vibration, Proceedings of the Ninth International Congress on Sound and Vibration, ICSV9, Orlando, USA, Invited Paper, July 2002.

Thomas L. Lagö and Sven Olsson, “Estimation of Doppler Shift Using The Symmiktos Method®: A non-linear Approach for Acoustic Doppler Current Meter Applications,” Proceedings of  InterNoise2002, July, 2002, Invited Paper.

Thomas L. Lagö and Sven Olsson, “A Novel Signal Model for Acoustic Doppler Current Meters Based on Large Real-life Data Sets,” Proceedings of InterNoise2002, July, 2002, Invited Paper.

Thomas L. Lagö, “Accurate Amplitude Measurements for Combined Tonal and Random Noise,” Accepted Paper for the EEAA 6th International Symposium, Transport Noise, June, St. Petersburg, 2002 Invited Paper.

Thomas L. Lagö, “Loudspeaker Placement for Enhanced Monitor Sound and Source Positioning,” Accepted Paper for the AES 21st International Conference on Architectural Acoustics and Sound Reinforcement, June 1-3, St. Petersburg, 2002, Invited Paper.

Thomas L. Lagö, “A Pseudo-Random Mathematical Approach to Railroad Noise Optimization,” Accepted Abstract for EEAA 6th International Symposium – Transport Noise, June 4-6, St. Petersburg, 2002, Invited Paper.

Thomas L. Lagö, “Not Using the 2*fmax as the Sampling Criteria for Efficient Analog to Digital Conversion,” Accepted Paper for the ISMA Noise and Vibration Engineering Conference, Leuven, Belgium, Invited Paper, September 16-18, 2002.

Thomas Lagö, Sven Olsson, Ingvar Claesson and Lars H kansson, “Design of an Efficient Chatter Control System for Turning and Boring Applications,” Society for Experimental Mechanics, Proceedings of the Twentieth International Modal Analysis Conference, IMAC-XX, [Pat], Los Angeles, USA, February, 2002, Invited Paper.

Thomas L. Lagö, “Industry Overview of Active Control Methods and Applications,” Proceedings of Adaptronic Congress 2002, Interdisciplinary Forum on Adaptive Technologies and Systems in Industrial Applications, April 2002, Berlin Germany, Invited Paper.

Thomas Lagö, Sven Olsson, Ingvar Claesson and Lars H kansson, “Performance of a Chatter Control System for Turning and Boring Applications,” Proceedings of GRACM2002, June 2002, Patras, Greece, Invited Paper.

Thomas L. Lagö, “An MLS Approach to Railroad Noise Optimization,” Submitted Abstract for the 21st International Modal Analysis Conference, IMAC XXI, February, 2003, Invited Paper.

Sven Olsson and Thomas L. Lagö, “Multiple Peak Count Analysis, a Spectral Resolution Enhancement method using a-priori information,” CD-ROM Proceedings of the 21st International Modal Analysis Conference, IMAC XXI, February, 2003, Invited Paper, pages 1-8.

Sven Olsson and Thomas L. Lagö, “Center Frequency Estimation for non-Gaussian data using a non-linear method, The Symmiktos Method,” CD-ROM Proceedings of the 21st International Modal Analysis Conference, IMAC XXI, February, 2003, Invited Paper, pages 1-8.

Ingvar Claesson, Thomas L. Lagö, Sven Olsson, and Mattias Dahl, “An Innovative Time Window for High Accuracy Amplitude Measurements using the High Accuracy Flat Top Window” Accepted Abstract for the 21st International Modal Analysis Conference, IMAC XXI, February, 2003, Invited Paper.

Sven Olsson and Thomas L. Lagö, “Sound and Vibration Signal Classification using a combined linear and logarithmic pre-filtering approach,” Accepted Abstract for the 21st International Modal Analysis Conference, IMAC XXI, February, 2003, Invited Paper.

L. Håkansson, A. Brandt, T. L. Lagö and I. Claesson, “Modal Analysis and Operating Deflection Shapes of a Boring Bar,” CD-ROM Proceedings of the 21st International Modal Analysis Conference, IMAC XXI, February, 2003, Invited Paper, pages 1-8.

Thomas L. Lagö and Anders Brandt, Using Matlab for Advanced Noise and Vibration Analysis, “ WAC2004, SAE, USA 2004, Invited Paper.

Thomas L. Lagö and Anders Brandt, “Actual Accuracy in Flight Data Collection and Analysis, “ WAC2005, SAE, USA 2005, Invited Paper.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Analog versus Digital Control of Boring Bar Vibration,” Accepted for publication In proceedings of the SAE World Aerospace Congress, WAC, Dallas, Texas, USA, October 3-6, 2005.

H. Åkesson, A. Brandt, T. Lagö, L. Håkansson, I. Claesson, “Operational Modal Analysis of a Boring Bar During Cutting,” published at the 1st IOMAC conference, International Operational Modal Analysis Conference, April 26-27, 2005, Copenhagen, Denmark.

H. Åkesson, T. Smirnova, L. Håkansson, T. Lagö, I. Claesson, “Analog and Digital Approaches of Attenuation Boring Bar Vibrations During Metal Cutting Operations,” published at the 12th ICSV conference, Lisbon, Portugal, July 11 – 14, 2005.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson, A. Sigfridsson, T. Svensson and T. Lagö, “Active Boring Bar Prototype Tested in Industry,” Accepted Paper, Adaptronic Congress 2006, 03-04 May, Göttingen, Germany.

H.Åkesson, I. Gustavsson, L. Håkansson, I. Claesson and T. Lagö, “Vibration Analysis of Mechanical Structures over the Internet Integrated into Engineering Education,” In proceedings of the 2006 ASEE Annual Conference & Exposition, Chicago IL, June 18 – 21, 2006.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson, A. Sigfridsson, T. Svensson and T. Lagö, “A First Prototype of an Active Boring Bar Tested in Industry,” In Proceedings of the Twelfth International Congress on Sound and Vibration, ICSV12, Lisbon, Portugal, 11 – 14 July, 2006.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Identification of Spatial Dynamic Properties of the Boring Bar by means of Finite Element Model: Comparison with Experimental Modal Analysis and Euler-Bernoulli Model”, In Proceedings of the Twelfth International Congress on Sound and Vibration, ICSV12, Lisbon, Portugal, 11 – 14 July, 2006.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Comparison of different controllers in the active control of tool vibration; including abrupt changes in the engagement of metal cutting,” Sixth International Symposium on Active Noise and Vibration Control, ACTIVE, Adelaide, Australia, 18-20 September, 2006.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Investigation of Boring Bar Mode Shape Rotation by Experimental Modal Analysis in Correlation with Finite Element Modeling,” Noise and Vibration Engineering Conference, ISMA2006, Leuven, Belgium, 18 – 20 September 2006.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Building an Accurate Finite Element Model of the Boring Bar with “Free-Free” Boundary Conditions: Correlation to Experimental Modal Analysis and Euler-Bernoulli Model,” Noise and Vibration Engineering Conference, ISMA, Leuven, Belgium, 18 – 20 September 2006.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Vibration in Turning and the Active Control of Tool Vibration”, Second World Congress on Engineering Asset Management and the Fourth International Conference on Condition Monitoring, Harrogate, UK, 11-14 June, 2007.

Thomas L. Lagö, “Condition Based Monitoring, Friend or Foe?”  The Fourth International Conference on Condition Monitoring June 11-14, 2007, England, Keynote Address.

Thomas L. Lagö, “Overview on Adaptronics and the Future with Smart Embedded Systems, “Adaptronic Congress, 2007, Göttingen, Germany, Keynote Address.

I. Gustavsson, J. Zackrisson, L. H kansson, I. Claesson and T. Lagö, “The VISIR project – an Open Source Software Initiative for Distributed Online Laboratories”, In proceedings of REV 2007 International Conference on Remote Engineering and Virtual Instrumentation, Porto, Portugal 25-27 June 2007.

H.  kesson, T. Smirnova, L. H kansson, I. Claesson and T. Lagö, “Investigation of the Dynamic Properties of a Boring Bar Concerning Different Boundary Conditions,” ICSV14 – The Fourteenth International Congress on Sound and Vibration, Cairns, Australia, 9-12 July, 2007.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Initial Experiments with a Finite Element Model of an Active Boring Bar, ICSV14 – The Fourteenth International Congress on Sound and Vibration, Cairns, Australia, 9 – 12 July, 2007.

Thomas L. Lagö, “Condition Based Monitoring – How to make it a Friend,“ The Fifth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 15-18 July 2008, The Edinburgh Conference Centre, Heriot-Watt University, Edinburgh, Scotland, Keynote Address.

I. Gustavsson, J. Zackrisson, J Ström Bartunek, Kristian Nilsson, L. H kansson, I. Claesson, and T. Lagö, “Telemanipulator for Remote Wiring of Electrical Circuits,” Proceedings of the 2008 REV Conference, Düsseldorf, Germany, June 22 – 25, 2008.

Thomas L. Lagö, Henrik  Åkesson and Hector Lobo, “Condition Monitoring Solutions as a Tool to Reduce Refit Duration, “ Navy Conference, NATIONAL SYMPOSIUM ON ACOUSTICS (NSA 2008), December 22-24, 2008, Visakhapatnam, India.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Initial Experiments With a Finite Element Model of an Active Boring Bar,” ICSV14 – The Fourteenth International Congress on Sound and Vibration, Cairns, Australia, 9-12 July, 2007.

H. Åkesson, T. Smirnova, L. H kansson, I. Claesson, A. Sigfridsson, T. Svensson and T. Lagö, “Investigation of the Dynamic Properties of a Passive Damped Boring Bar,” In Proceedings of Adaptronic Congress, Berlin, Germany, 20 – 21 May, 2008.

I. Gustavsson, J. Zackrisson, Kristian Nilsson, Javier Garcia-Zubia, L. H kansson, I. Claesson, and T. Lagö, “A Flexible Instructional Electronics Laboratory with Local and Remote Lab Workbenches in a Grid,” Proceedings of the 2nd International Workshop on e-learning and Virtual and Remote Laboratories, Potsdam, Germany, February 14 – 15, 2008.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Modeling a Clamped Boring Bar using Euler-Bernoulli Beam Models with Various Boundary Conditions,” MMWP08 – The third International Conference on Mathematical Modeling of Wave Phenomena, Växjö, v1106, pp 149-156, Sweden, 9-13 June, 2008.

H.  kesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Advantages and Drawbacks Using Different Sensors in Feedback Control in Active Boring Bar Applications,” ICSV15 – The 15th International Congress on Sound and Vibration, Daejon, Korea, 6 – 10 July, 2008.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Investigation Concerning Actuator Position in an Active Boring Bar Regarding it s Performance by Means of “3-D” Finite Element Models,” ICSV15 – The 15th International Congress on Sound and Vibration, Daejon, Korea, 6 – 10 July, 2008.

T. Lagö, L. Håkansson and H. Åkesson, “Classification of metal cutting vibrations, is it all chatter?,” In Proceedings of Fifth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Edinburgh, Scotland, UK, 15 – 18 July, 2008.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Dynamic Properties of Tooling Structure: Hydraulic Clamping versus Standard Screw Clamping in a Lathe Application,” Ninth International Conference on Computational Structures Technology, Athens, Greece, 2-5 September, 2008.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Estimation of an active boring bar s control path FRF:s by means of its 3-D FE-model with Coulomb friction,” The Ninth International Conference on Computational Structures Technology, Athens, Greece, 2-5 September, 2008.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Developments Steps of an Active Boring Bar for Industrial Application,” Internoise, Shanghai, China, 26-29 October, 2008.

M. Winberg, H. Åkesson, T. Lagö, and I. Claesson, “Acoustical Measurements Using a Virtual Microphone Technique,” Internoise, Shanghai, China, 26-29 October, 2008.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Investigations of Possibilities of Improvement of a Finite Element Model of an Active Boring Bar”, International Modal Analysis Conference-XXVII(IMAC-XXVII), Orlando, Florida USA, 9-12 February 2009.

H.  kesson, T. Smirnova, L. H kansson, I. Claesson and T. Lagö, “Investigation of the Dynamic Properties of a Milling Structure; Using a Tool Holder with Moderate Overhang,” IMAC XXVII, Orlando, USA, 9-12 February, 2009.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Accurate FEM modeling of a Boring Bar Correlated with Experimental Modal Analysis,” IMAC XXVII, Orlando, USA, 9-12 February, 2009.

H. Åkesson, A. Sigfridsson, T. Lagö, I. Andersson and L. Håkansson, “Noise Source Identification and Active Control in a Water Turbine Application,” In Proceedings of The Sixth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Dublin, Ireland, 23-25 June, 2009.

T. Smirnova, H. Åkesson, I. Claesson, L. Håkansson and T. Lagö, “Modeling a Clamped Boring Bar using Euler-Bernoulli Beam Models with Various Boundary Conditions,”3rd Conference on Mathematical Modeling of Wave Phenomena/20th Nordic Conference on Radio Science and Communications, v1106, p149-156, 2009.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Investigation Concerning Dynamic Properties of an Active Boring Bar Regarding its Performance by Means of “1-D” Finite Element Models,”ICSV16 – The Sixteenth International Congress on Sound and Vibration, Krakow, Poland, 5-9 July, 2009.

H. Åkesson, T. Smirnova, L. Håkansson, I. Claesson and T. Lagö, “Preliminary investigation of active control of a milling tool holder,” ACTIVE 2009 – The 2009 International Symposium on Active Control of Sound and Vibration, Ottawa, Canada, 20-22 August, 2009.

Thomas Lagö and Kristian Nilsson, “The VISIR™ Open Lab Platform brings the laboratory online,” NI Week, Austin, Texas, 2009.

T. Smirnova, H. Åkesson, L. Håkansson, I. Claesson and T. Lagö, “Simulation of Active Suppression of Boring Bar Vibrations by Means of Boring Bar’s “1-D” Finite Element Model,” ACTIVE 2009 – The 2009 International Symposium on Active Control of Sound and Vibration, Ottawa, Canada, 20-22 August, 2009.

Thomas L. Lagö, “Robust and Rapid Production Line Testing,” The Sixth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, June 23-25 2009, Stillorgan Park Hotel, Dublin, Ireland, Keynote Address.

H. Åkesson, A. Sigfridsson, T. Lagö, I. Andersson and L. Håkansson, “Noise Source Identification and Active Control in a Water Turbine Application,” Proceedings of The Sixth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Dublin, Ireland, 23-25 June, 2009.

Thomas L. Lagö and Henrik Åkesson, “Vibration Absorption and Health Monitoring in a Hydroelectric Power Plant,” Proceedings of ICSV17 – The Seventeenth International Congress on Sound and Vibration, 18-22 July, 2010, CAIRO.

H. Åkesson, A. Sigfridsson, T. Lagö, L. Håkansson, and I. Claesson, “Active Control of Turbine Vibration and Conditioning Based Monitoring,” Proceedings of ICSV17 – The Seventeenth International Congress on Sound and Vibration, Cairo, Egypt, 18-22 July, 2010.

Thomas Lagö and Henrik  Åkesson, “Non contact vibration measurements using an ultrasound method – pros- and cons,” CM 2011 and MFPT 2011, The Eighth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 20-22 June 2011, Cardiff, Wales, UK.

Thomas Lagö, “Condition Monitoring Solutions with Prognosis Capabilities,” CM 2011 and MFPT 2011, The Eighth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 20-22 June 2011, Cardiff, Wales, UK.

Ingvar Gustavsson, Kristian Nilsson, Thomas Lagö,  Ingvar Claesson, Lars Håkansson, “VISIR – Open Platforms for New Teaching Abilities,” CM 2011 and MFPT 2011, The Eighth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 20-22 June 2011, Cardiff, Wales, UK.

Thomas Lagö,  “ Condition Monitoring Solutions with a Focus on Prognosis Capabilities,” Proceedings of the International Conference on Maintenance, Performance, Measurement and Management. December 14, Lule  2011.

Thomas L. Lagö, “Rapid Methods for Production Line Testing of Small Electrical Motors,” MFPT, The Prognostics and Health Management Solutions Conference. 24-26 April 2012 – Crowne Plaza Hotel, Dayton, OH, USA.

Thomas L. Lagö, “ Human Listening as a Classification Tool in Production Lines, “ MFPT, The Prognostics and Health Management Solutions Conference. 24-26 April 2012 – Crowne Plaza Hotel, Dayton, OH, USA.

Thomas L. Lagö, “ Proper Amplitude Estimation Strategies for CBM Applications“, MFPT, The Prognostics and Health Management Solutions Conference. 24-26 April 2012 – Crowne Plaza Hotel, Dayton, OH, USA.

Thomas L. Lagö, “Condition Monitoring Requirements with a Focus on Prognosis Success,” Proceedings of the Nordic Maintenance World Congress, 14-15 March 2012, Gothenburg, Sweden, Invited Keynote Address.

Thomas L. Lagö, “Automatic Amplitude Estimation Strategies for CBM Applications, “ 18th World Conference on Nondestructive Testing, 16-20 April 2012, Durban, South Africa.

Jay Nkuna, Thomas L. Lagö, “Robust Classification of Gearbox Faults by means of Vibration Condition Monitoring and Evolutionary Optimisation of Kohonen’s Self-Organising Maps, “ 18th World Conference on Nondestructive Testing, 16-20 April 2012, Durban, South Africa.

Thomas L. Lagö, “Human Listening Tests In Production Lines,” CM2012, Proceedings of The Ninth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies at The Earl’s Court Ibis Hotel, London, UK.

Thomas L. Lagö, “How to properly find amplitude values in CBM applications,” CM2012, Proceedings of The Ninth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies at The Earl’s Court Ibis Hotel, London, UK.

Thomas L. Lagö, “Production Line Testing of Small Electrical Motors,” CM2012, Proceedings of The Ninth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies at The Earl’s Court Ibis Hotel, London, UK.

Thomas L. Lagö and Jay Nkuna, “Robust Classification of Gearbox Faults by means of Vibration Condition Monitoring and Evolutionary Optimisation of Kohonen’s Self-Organizing Maps,” CM2012, Proceedings of The Ninth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies at The Earl’s Court Ibis Hotel, London, UK.

Jay Nkuna and Thomas Lagö, “Parallel classification of rolling element bearing faults based on  fuzzy logic  and Kohonen’s Self-Organising Maps,” 18th World Conference on Non-Destructive Testing (WCNDT2012), Durban, South Africa, April 15-20, 2012.

Thomas L. Lagö, “Amplitude Errors due to Sparse Sampling Following Shannon,” MPMM 2012 Conference, Maintenance, Performance, Measurement & Management, 12th & 13th September 2012, University of Sunderland, Great Britain.

Thomas L. Lagö, “An Automatic Approach for Proper Amplitude Estimation in CBM Applications,” Proceedings of CM2013/MFPT2013 The Tenth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 18-20 June 2013, Qubus Hotel, Kraków, Poland.

Thomas L. Lagö, “Discretization’s Impact on Time Domain Analysis,” Proceedings of CM2013/MFPT2013 The Tenth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 18-20 June 2013, Qubus Hotel, Kraków, Poland.

Thomas L. Lagö and Alan Boyer, “International Experiences from a New Sound System Approach,” 134th AES Convention e-Brief, Fontana de Trevi Conference Center, May 4-7 2013, Rome, Italy.

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, ”NEW E-LEARNING APPROACHES FOR SOUND AND VIBRATION APPLICATIONS,” 6th International Conference from Scientific Computing to Computational Engineering, Athens, Greece, 9-12 July, 2014.

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, “NEW e-LEARNING AND MOOC APPROACHES FOR CBM APPLICATIONS, “ Conference Proceedings of BINDT (British Institute for Non-destructive Testing), June 10-12, 2014, Marriott Hotel, Manchester, Great Britain.

Thomas L. Lagö and Alan Boyer, “ DYNAMIC SIGNAL PROCESSING APPROACHES FOR BETTER SPEECH INTELLIGIBILITY IN MUSIC ACOUSTICS APPLICATIONS,” Proceedings of the 21st International Congress on Sound and Vibration, ICSV, 13-17 July, 2014, Beijing/China.

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, EFFECTIVE ACCURACY CONTROL FOR CBM APPLICATIONS,” Conference Proceedings of MFPT (the Society for Machinery Failure Prevention Technology), May 20-22, 2014,  Sheraton Oceanfront Hotel, Virginia Beach, VA, USA.

Thomas L. Lagö, Valdi Ivancic, and Alan Boyer, ”NEW E-LEARNING SYSTEMS FOR CBM APPLICATIONS,” Conference Proceedings of MFPT (the Society for Machinery Failure Prevention Technology), May 20-22, 2014,  Sheraton Oceanfront Hotel, Virginia Beach, VA, USA.

Erkki Jantunen, Idriss El-Thalji, David Baglee and Thomas L. Lagö, “Problems with using Fast Fourier Transform for rotating equipment: Is it time for an update? ” Proceedings of Comadem 2014, 27th International Congress of Condition Monitoring and Diagnostic Engineering, 16-18 September 2014, Brisbane, Australia.

Thomas L. Lagö and Alan Boyer, EFFECTIVE ACCURACY CONTROL FOR CBM APPLICATIONS,” CM2014/MFPT2014 Conference Proceedings of BINDT (British Institute for Non-destructive Testing), June 10-12, 2014, Marriott Hotel, Manchester, Great Britain.

Thomas L. Lagö, Alan Boyer, Dan Peterson and Nils Svendenius, “Green and Sustainable Technologies for the Future of Automotive, ” Proceedings of the SAE India/SIAT/ARAI conference January 19-25 2015, Pune, India. Invited Keynote.

Thomas L. Lagö and Alan Boyer, “Real-Time Fast Tracking of Varying RPM Using an On-Line Method without a Tachometer,” Proceedings of MFPT 2015 and ISA’s 61st International Instrumentation Symposium,  May 12-14, 2015 – The Westin, Huntsville, AL, Unites States.

Thomas L. Lagö and Alan Boyer, “Cepstrum Analysis Basics for the Interested,” Proceedings of MFPT 2015 and ISA’s 61st International Instrumentation Symposium,  May 12-14, 2015 – The Westin, Huntsville, AL, Unites States.

Thomas L. Lagö, Tommy Forsell, Valdi Ivancic and Alan Boyer, “Experiences from CBM Educational Approaches in Sweden,” Proceedings of MFPT 2015 and ISA’s 61st International Instrumentation Symposium,  May 12-14, 2015 – The Westin, Huntsville, AL, Unites States.

Research Reports, Text Books, Books etc.

T. Lagö and S. Olsson, “Amplitude and Phase Measurements,” Master of Science Thesis, Electrical Engineering, Lund Institute of Technology, Lund, 1982.

I. Claesson, T. Lagö and G. Salomonsson, “Estimation of Varying Ultrasonic Attenuation In Soft Tissue”, Technical Report TR-176, Lund Institute of Technology, Department of Telecommunication Theory, Lund Sweden, 1983.

T. Lagö, “An Acoustic Doppler Current Meter, Methods and Principles”, Licentiate Thesis, ISRN KTH/FKT/FR– 95/26–SE, Royal Institute of Technology, The Marcus Wallenberg Laboratory, Stockholm, May 1995, Sweden, (166 pages).

Thomas L. Lagö, “Frequency Analysis of Helicopter Sound in the AS332 Super Puma,” Technical Report ISSN 1103-1581, ISRN Blekinge Institute of Technology -RES–96/8–SE.

Thomas L. Lagö, “A Novel Signal Model and Estimation Method for Acoustic Doppler Current Meters,” Doctoral Thesis, Lund University, LTH, Civil Engineering, department of Engineering Acoustics, LUTVDG/TVBA–99/1007–SE, (1-526), ISSN: 0281-8477, Lund, Sweden, 1999, (628 pages).

Thomas L. Lagö and Sven Olsson, “Various Signal Processing Techniques used on non-Stationary Acoustic Doppler Current Data,” Research Report 2/99, ISSN 1103-1581, ISRN HK/R-RES-99/2-SE, Volume I-XI, Blekinge Institute of Technology, Ronneby, 1999, Sweden, (each volume abt 500 pages, 11 volumes).

H. Åkesson, T. Smirnova, T. Lagö and L. Håkansson “Analysis of Dynamic Properties of Boring Bars Concerning Different Clamping Conditions”, Research report No 2007:06, ISSN 1101-1581, 2007.

H. Åkesson, T. Smirnova, T. Lagö and L. Håkansson “Investigation of Dynamic Properties of a Milling Tool Holder”, Research report No 2009:14, Blekinge Institute of Technology, ISSN 1103-1581, November 2009.

Ingvar Gustavsson, L. Claesson, K. Nilsson, J. Zackrisson, J. Z. J. Ström Bartunek, T. Lagö, I. Claesson, Chapter in The VISIR Open Lab Platform accepted for publication in Internet Accessible Remote Laboratories: Scalable E-learning Tools for Engineering and Science Disciplines, M. E. Auer, V. J. Harward and A. K. M. Azad (ed.), IGI Global, 2011.

Thomas L. Lagö, Chapter 10, “Digital Processing of Vibration Signals”, in “Engineering Principles of Mechanical Vibration,” by Douglas D. Reynolds, published by Trafford, eBook ISBN 9781426907982, Print ISBN 9781426907968, 2009.

Thomas L. Lagö, Chapter 9, “VIBRATION MEASUREMENTS”, in “Engineering Principles of Mechanical Vibration,” by Douglas D. Reynolds, published by Trafford, eBook ISBN 9781426907982, Print ISBN 9781426907968, 2009.

Thomas Lagö has participated in the creation of the book COLLABORATE, The Art of WE, combining capabilities to create new opportunities for success, by Dan Sanker, Jossey-Bass, An Imprint of John Wiley & Sons, ISBN 978-1-118-11472-8, 2012.

International Conferences (peer review not always used)

T. Lagö, P. Eriksson, “An Acoustic Doppler Current Meter based on the Symmiktos Method,” Radio Vetenskaplig Konferens RVK – 93, Sweden, April 1993.

T. Lagö, I. Claesson, “Hur analyserar jag en okänd signal”,Scandinavian Vibration Society, SVIB, April 25- 26, 1995, Ronneby, Sweden.

Thomas L. Lagö och Ingvar Claesson, “Hur analyserar jag en okänd signal?,” Scandinavian Vibration Society, AU-1 conference, Ronneby, April 1995.

Thomas L. Lagö, “Frekvensanalys med FFT respektive digitala filter,” Scandinavian Vibration Society, SVIB, AU-1 conference, Täby Park Hotel, January 1997.

Thomas L. Lagö, “Tumregler för klassificering av vibrationssignaler, ”Scandinavian Vibration Society, SVIB, AU-1 conference, Täby Park Hotel, January, 1997.

Thomas L. Lagö, “Communication Comfort for Helicopter Pilots,” The Swedish Acoustical Society, SAS, Stockholm, 1997.

T.L. Lagö, “Högskolan i Karlskrona/Ronneby främst i internationell forskarutvärdering!”, Scandinavian Vibration Society Magazine, SVIB-news, number 3, October, 1997.

P. Sjösten, T. L. Lagö, “Aktiv dämpning av framtidens X2000-t g,” Scandinavian Vibration Society, SVIB, November 1996.

S. Johansson, S. Nordebo, T. L. Lagö, P. Sjösten and I. Claesson, “Algorithms for Active Noise Control in Propeller Aircraft,” Scandinavian Vibration Society, SVIB AU-5 Conference, Marcus Wallenberg Laboratory, KTH, November 1997.

Thomas L. Lagö, Dan Maquire, Per Lindberg and Anders Brandt, “Analog to Digital Conversion – Old and New Methods and their Features,“ SVIB AU1 Conference, Helsingborg, 2008, Sweden.

Thomas L. Lagö, Dan Maguire, Anders Brandt and Kenneth Andersson, “Sensor and Actuator Development versus New ADC Improvements, “ SVIB AU1 Conference, Helsingborg, 2008, Sweden.

I. Gustavsson, M. Pettersson, L. Håkansson, T. Lagö, and I. Claesson, “Gör ingenjörsutbildningen attraktiv genom att öka det experimentella inslaget “, Ingenjörsutbildningarnas utvecklingskonferens, Royal Institute of Technology, Stockholm, Sweden, November 26-27, 2008.

Thomas L. Lagö, “Smart Embedded Systems, A New Vibration Strategy,” Embedded Conference, Tekniska Mässan, Stockholm, 2006.

Thomas L. Lagö, Henrik Åkesson, Andreas Sigfridsson, Magnus Lindman, Tomas Svärd and Christer Cederqvist, “Acoustically optimized sound barriers for less environmental noise pollution,” Scandinavian Vibration Society SVIB, Vibration Day, Nov 2010, Linköping, Sweden.

Thomas L. Lagö, Henrik Åkesson, Andreas Sigfridsson and Magnus Lindman, “A new generation seats with excellent impact and damping properties for drivers in tough applications,” Scandinavian Vibration Society SVIB, Vibration Day, Nov 2010, Linköping, Sweden.

Henrik Åkesson, Thomas Lagö, Lars Håkansson and Ingvar Andersson, “Noise Source Identification and Active Control in a Water Turbine Application,” Scandinavian Vibration Society, SVIB, 2009 Yearly Meeting, November 2009, Gothenburg, Sweden.

Thomas Lagö, “Green Buildings,“ E-days Göteborg, November 2010.

Thomas Lagö, “Doing Business in the USA,” US Embassy INVEST IN AMERICA SEMINAR, March 9, Stockholm, 2010.

Thomas Lagö, US Embassy Conference “ATLANTIC CROSSING – A CONFERENCE ABOUT SUCCESS (and failure)  in the USA,” Stockholm, August19, 2010.

Thomas L. Lagö, “Innovationer och entreprenörskap – modeord eller verklighet?,” IUC Öst Conference on Innovation Systems, May 2012, Sweden.

European Community Research Projects

Thomas Lagö and Sylvie Capelle, “Test Procedures and Requirements for Determination of Cabin Acoustics Behavior During Different Flight Conditions,” ASANCA-II Deliverable D71, January 1995.

S. Johansson, S. Nordebo, T.L. Lagö, P. Sjösten, I. Claesson, ”Evaluation Report: Comparison Between a Single-versus a Multiple-Reference MIMO ANC Controller,” ASANCA-II Deliverable D90, February 1998.

P. Persson, S. Johansson, P. Sjösten, T.L. Lagö, I. Claesson, ”Evaluation Report: Concluding Report for Active Noise and Vibration Control Algorithms,” ASANCA-II Deliverable D118, February 1998.

Sven Johansson, Per Sjösten, Thomas Lagö, Sven Nordebo and Ingvar Claesson, “Final Report on Work Related to Multireference System,” ASANCA-II Deliverable D76-2, April 1996.

S. Johansson, S. Nordebo, T.L. Lagö, P. Sjösten, “Comparison study of MR-MIMO and SR-MIMO algorithm performance on simulated and Dornier 328 test data,” ASANCA-II Workshop, Naples, Italy, November 1996.

S. Johansson, T.L. Lagö, P. Sjösten, I. Claesson, “Sensitivity and robustness of an X-LMS feedforward system to different contaminating noise sources,” ASANCA-II Workshop, Naples, Italy, November 1996.

Sven Nordebo, S. Johansson, Per Sjösten, Thomas Lagö, Ingvar Claesson, “Algorithm Simulation Results and Evaluations,” ASANCA-II Deliverable D81, November 1996.

Per Sjösten, Mathias Winberg, Sven Johansson, Thomas Lagö, Sven Nordebo, Ingvar Claesson, “Developed Computer Codes in Adequate Format and Media,” ASANCA-II Deliverable D83, November 1996.

Per Sjösten, Mathias Winberg, Sven Johansson, Thomas Lagö, Sven Nordebo, Ingvar Claesson, “Test Procedures and Requirements for Performance and Validation of Robustness of Self Tuning Regulator Algorithm and Algorithm Using Two Tacho Signals,” ASANCA-II Deliverable D84, November 1996.

Per Sjösten, Mathias Winberg, Sven Johansson, Thomas Lagö, Sven Nordebo, Ingvar Claesson, “Computer Code in C-Language on Adequate Media of the Algorithm to be Implemented and of Fundamental Test-programs,” ASANCA-II Deliverable D87, November 1996.

Sven Johansson, Per Sjösten, Thomas Lagö, Sven Nordebo, Ingvar Claesson, “Final Report on Comparsion Study Between Single and Twin Tacho Signal Use,” ASANCA-II Deliverable D79-2, June 1996.

Sven Johansson, Per Sjösten, Thomas Lagö, Sven Nordebo, Ingvar Claesson, “Final Report on Work Related to Multireference System,” ASANCA-II Deliverable D76-2, April 1996.

Sven Johansson, Per Sjösten, Thomas Lagö, Sven Nordebo and Ingvar Claesson, “Comparison Study Between Single and Twin Tacho Signal Use,” ASANCA-II Deliverable D79, December 1995.

Sven Johansson, Per Sjösten, Thomas Lagö, Sven Nordebo and Ingvar Claesson, “New and Extended Control Methods,” ASANCA-II Deliverable D76, June 1995

Mattias Dahl, Per Sjösten and Thomas L. Lagö, “Multiple Reference, Multiple Input, Multiple Output Control of Sound Fields,” 1st ASANCA-II Workshop, D123/D124, Naples, Italy, October, 1995.

Sven Johansson, Per Sjösten and Thomas L. Lagö, “Adaptive Signal Processing with the LMS Algorithm,” 1st ASANCA-II Workshop, D123/D124, Naples, Italy, October, 1995.

Thomas Lagö and Sven Olsson, “The Characteristics of Speaking Panels,” ASANCA-II Deliverable D50/B, June 1995.

In all of these EU projects, Dr. Lagö has been the project leader and the person responsible for all written material. However, part of supervising the Ph.D. students was to make them learn how to write and present the material. Thus, Dr. Lagö motivated the students to do the key writing, under his supervision, and that is why his name is not first. The principle usually followed has been that the person writing the text gets the first name.